Difference between revisions of "Toner Transfer"
Jump to navigation
Jump to search
m (→External Links) |
|||
| (23 intermediate revisions by 11 users not shown) | |||
| Line 1: | Line 1: | ||
| − | [ | + | Toner Transfer, like [[photoetching]], is a popular [[techniques | PCB fabrication technique]]. |
| + | |||
| + | == Introduction == | ||
| + | |||
| + | Press-and-Peel(tm), photoresist, Sharpie, nail polish... | ||
I have used this method for etching some fairly fine lines when fabricating a microstrip microwave filter using Tom Gootee's method linked to below. My two cents on this is the fact that the type of toner you use matters. In an admittedly small sample set of two different printers, the genuine HP microfine toner performed far better than the generic toner that was installed in a second printer that we tried. We used the Staple's glossy inkjet paper, and with the HP toner, it worked quite well. | I have used this method for etching some fairly fine lines when fabricating a microstrip microwave filter using Tom Gootee's method linked to below. My two cents on this is the fact that the type of toner you use matters. In an admittedly small sample set of two different printers, the genuine HP microfine toner performed far better than the generic toner that was installed in a second printer that we tried. We used the Staple's glossy inkjet paper, and with the HP toner, it worked quite well. | ||
Also, the etching solution of 1 part muriatic acid to 2 parts hydrogen peroxide is worlds better than the ferric chloride solution as it is clear and doesn't stain everything it touches. It is also available locally (hydrogen peroxide is in every drug and grocery store, muriatic acid can be found at almost any hardware store). | Also, the etching solution of 1 part muriatic acid to 2 parts hydrogen peroxide is worlds better than the ferric chloride solution as it is clear and doesn't stain everything it touches. It is also available locally (hydrogen peroxide is in every drug and grocery store, muriatic acid can be found at almost any hardware store). | ||
| + | See [[Chemical Etchants]] for details. | ||
Thankfully, we worked in a school lab that had access to pure acetone for cleaning off the traces, so we didn't have to resort to foul-smelling nail polish. | Thankfully, we worked in a school lab that had access to pure acetone for cleaning off the traces, so we didn't have to resort to foul-smelling nail polish. | ||
| + | |||
| + | == Toner Transfer Tip and Tricks From around the World == | ||
| + | |||
| + | Leave your tips and tricks here, it is ok if you found it on the web (give reference if you have them) or if you picked it up somewhere else even figured it out yourself. If you have a long write up do not leave it here, make a new page and link to it. | ||
| + | |||
| + | |||
| + | === Paper === | ||
| + | |||
| + | Experiment with paper, keep shifting around to find the right stuff. I use magazine paper. You want a glaze (usually clay) so the toner will transfer, and soluble paper so you can easily remove it. Right now, my favorite is the RISDI catalog. If the paper is too thin it may jam in the printer (check printer settings by the way). Some have suggested attaching (perhaps just by folding the leading edge over) it to standard paper as a carrier to get it through the printer. There are, of course, photo papers for laser printers and stuff made just for toner transfer. | ||
| + | |||
| + | === Roller === | ||
| + | |||
| + | A roller may help focus pressure, especially at the edges. This has to be done while hot. One way I have seen is to put a dowel (perhaps several) under the board and roll back and forth on that. | ||
| + | |||
| + | === Padding === | ||
| + | |||
| + | A couple of layers of paper towel as padding between the board and the iron can help even out the pressure and improve adhesion at the edges. | ||
| + | |||
| + | === Electric Grill as Ironing Board === | ||
| + | |||
| + | I [[russ_hensel]] was having trouble getting enough heat. My breakthrough was to use a temperature controlled electric grill (great for pan cakes by the way) set for 350°f and iron as usual. | ||
| + | |||
| + | === Remember high temperature is required === | ||
| + | |||
| + | This is not like ironing a shirt, the thing has to get hot, move the iron slowly or almost not at all. Pressure is good, experiment to find out how much. | ||
| + | |||
| + | === Edges === | ||
| + | |||
| + | The edges are usually the problem focus your attention there, if you get the edges you will probably do fine on the center with only minimal attention there. | ||
| + | |||
| + | == Touchup == | ||
| + | |||
| + | Touchup with a Sharpie marker. | ||
| + | Some people (such as Stefan Vorkoetter) draw their entire board with the Sharpie marker, completely bypassing all that hassle with computers, laser printers, special paper, ironing, etc. | ||
| + | |||
| + | Scrape off any toner or Sharpie ink that is covering metal you don't want. | ||
| + | |||
| + | Now you're ready to drop it in the [[Chemical Etchants]]. | ||
== External Links == | == External Links == | ||
| + | * [http://paulwanamaker.wordpress.com/perfect-single-or-double-sided-pcbs-with-the-toner-transfer-method/ "Perfect Single or Double Sided PCBs with the Toner transfer Method"] by Paul Wanamaker 2012 | ||
| + | |||
| + | * [http://www.stefanv.com/electronics/etching.htm "Making Excellent Printed Circuit Boards"] by Stefan Vorkoetter | ||
| + | |||
| + | * [http://www.esmonde-white.com/home/diversions/etching-a-copper-pcb "Etching a Copper PCB using Toner Transfer and Peroxide/HCl"] by Francis Esmonde-White | ||
| + | |||
| + | * [http://www.pulsarprofx.com/PCB/a_Pages/1_Menu/overview.html Direct Etch PCBs] These guys are selling a product for toner transfer, might be good or bad, ( how about a review by a user? ) but in any case they also have a bunch of very useful tips. | ||
| + | |||
* [http://www.ceunes.ufes.br/downloads/2/sandramuller-pci_metodo_termico.pdf Tonner transfer - By Lucas Zampar Bernardi - Article in Brasilian Portuguese] | * [http://www.ceunes.ufes.br/downloads/2/sandramuller-pci_metodo_termico.pdf Tonner transfer - By Lucas Zampar Bernardi - Article in Brasilian Portuguese] | ||
| − | * [http://www.veys.com/ | + | * [http://www.veys.com/2001/11/21/making-home-made-pcbs Toner transfer] |
* [http://www.fullnet.com/u/tomg/gooteepc.htm Toner transfer - by Tom Gootee] | * [http://www.fullnet.com/u/tomg/gooteepc.htm Toner transfer - by Tom Gootee] | ||
| − | * [http://karosium.com/ | + | * [http://www.karosium.com/2007/03/clean-simple-cheap-toner-transfer.html Clean, Simple, Cheap Toner Transfer - By Karo-sama] |
| + | |||
| + | * [http://diycircuits.net/makepcb/pcb_making PCB Making Photo Etching Toner Transfer including Using Matte Paper - by Hilary Cheng] | ||
| + | |||
| + | * [http://www.riccibitti.com/pcb/pcb.htm How to make PCBs at home in 1 hour & W I T H O U T special materials] | ||
| + | |||
| + | * [http://myweb.cableone.net/wheedal/pcb.htm Decent PCB's on the cheap.] | ||
| + | |||
| + | * [http://www.instructables.com/id/5pcb/ 5pcb] | ||
| + | * [http://www.instructables.com/id/Two-sided-PCB-using-toner-method/ Two sided PCB using toner method] | ||
| + | * [http://www.instructables.com/id/DIY_Printed_circuit_board/ DIY Printed circuit board ] A video, pretty good. | ||
| + | * [http://www.5bears.com/pcb.htm Printed Circuit Boards for the Masses] A pretty quick tutorial. | ||
| + | * [http://revision3.com/systm/etching/ Episode 15 PCB Etching] A video, the safety warnings are a bit over the top. | ||
| + | * [http://more.random.stuff.googlepages.com/howtomakepcbs How to make PCBs with a laser printer] | ||
| + | * [http://www.mouldy.org/making-a-pcb "Making a PCB"] toner transfer method; 0.1mm tracks; all surface mount with a tiny fine-pitch QFN IC. [http://www.mouldy.org/assembly later] he uses the Sparkfun tutorial for [[skillet reflow]]. | ||
| + | * [http://www.instructables.com/id/Quickie-PCB-Production-with-Bonus-NiCd-Battery-Ch/ "Quickie PCB Production (with Bonus NiCd Battery Charger)"] is entirely drawn with Sharpie markers (no computer, no laser printer). | ||
| + | * [http://www.dr-lex.be/hardware/tonertransfer.html Dr. Lex: Creating PCBs with the toner transfer method] | ||
| − | |||
[[Category:Techniques]] | [[Category:Techniques]] | ||
Latest revision as of 00:58, 14 March 2012
Toner Transfer, like photoetching, is a popular PCB fabrication technique.
Contents
Introduction[edit]
Press-and-Peel(tm), photoresist, Sharpie, nail polish...
I have used this method for etching some fairly fine lines when fabricating a microstrip microwave filter using Tom Gootee's method linked to below. My two cents on this is the fact that the type of toner you use matters. In an admittedly small sample set of two different printers, the genuine HP microfine toner performed far better than the generic toner that was installed in a second printer that we tried. We used the Staple's glossy inkjet paper, and with the HP toner, it worked quite well.
Also, the etching solution of 1 part muriatic acid to 2 parts hydrogen peroxide is worlds better than the ferric chloride solution as it is clear and doesn't stain everything it touches. It is also available locally (hydrogen peroxide is in every drug and grocery store, muriatic acid can be found at almost any hardware store). See Chemical Etchants for details.
Thankfully, we worked in a school lab that had access to pure acetone for cleaning off the traces, so we didn't have to resort to foul-smelling nail polish.
Toner Transfer Tip and Tricks From around the World[edit]
Leave your tips and tricks here, it is ok if you found it on the web (give reference if you have them) or if you picked it up somewhere else even figured it out yourself. If you have a long write up do not leave it here, make a new page and link to it.
Paper[edit]
Experiment with paper, keep shifting around to find the right stuff. I use magazine paper. You want a glaze (usually clay) so the toner will transfer, and soluble paper so you can easily remove it. Right now, my favorite is the RISDI catalog. If the paper is too thin it may jam in the printer (check printer settings by the way). Some have suggested attaching (perhaps just by folding the leading edge over) it to standard paper as a carrier to get it through the printer. There are, of course, photo papers for laser printers and stuff made just for toner transfer.
Roller[edit]
A roller may help focus pressure, especially at the edges. This has to be done while hot. One way I have seen is to put a dowel (perhaps several) under the board and roll back and forth on that.
Padding[edit]
A couple of layers of paper towel as padding between the board and the iron can help even out the pressure and improve adhesion at the edges.
Electric Grill as Ironing Board[edit]
I russ_hensel was having trouble getting enough heat. My breakthrough was to use a temperature controlled electric grill (great for pan cakes by the way) set for 350°f and iron as usual.
Remember high temperature is required[edit]
This is not like ironing a shirt, the thing has to get hot, move the iron slowly or almost not at all. Pressure is good, experiment to find out how much.
Edges[edit]
The edges are usually the problem focus your attention there, if you get the edges you will probably do fine on the center with only minimal attention there.
Touchup[edit]
Touchup with a Sharpie marker. Some people (such as Stefan Vorkoetter) draw their entire board with the Sharpie marker, completely bypassing all that hassle with computers, laser printers, special paper, ironing, etc.
Scrape off any toner or Sharpie ink that is covering metal you don't want.
Now you're ready to drop it in the Chemical Etchants.
External Links[edit]
- "Perfect Single or Double Sided PCBs with the Toner transfer Method" by Paul Wanamaker 2012
- "Making Excellent Printed Circuit Boards" by Stefan Vorkoetter
- "Etching a Copper PCB using Toner Transfer and Peroxide/HCl" by Francis Esmonde-White
- Direct Etch PCBs These guys are selling a product for toner transfer, might be good or bad, ( how about a review by a user? ) but in any case they also have a bunch of very useful tips.
- 5pcb
- Two sided PCB using toner method
- DIY Printed circuit board A video, pretty good.
- Printed Circuit Boards for the Masses A pretty quick tutorial.
- Episode 15 PCB Etching A video, the safety warnings are a bit over the top.
- How to make PCBs with a laser printer
- "Making a PCB" toner transfer method; 0.1mm tracks; all surface mount with a tiny fine-pitch QFN IC. later he uses the Sparkfun tutorial for skillet reflow.
- "Quickie PCB Production (with Bonus NiCd Battery Charger)" is entirely drawn with Sharpie markers (no computer, no laser printer).
- Dr. Lex: Creating PCBs with the toner transfer method
