Pi Setup Dec 2017 Stretch

From OpenCircuits
(Difference between revisions)
Jump to: navigation, search
(using fstab)
(using fstab)
 
Line 157: Line 157:
 
//192.168.0.170/share/_Source/rPi /mnt/share1 cifs user=russ,pass=squeak13,_netdev 0,0
 
//192.168.0.170/share/_Source/rPi /mnt/share1 cifs user=russ,pass=squeak13,_netdev 0,0
  
 +
If you make a new entry in fstab it will not auto-mount. Therefore you must reload / refresh the entries. A reboot will do this but that is not a friendly way to do it. A quick way to reload new entries in /etc/fstab (fstab) is to use the mount command:
 +
 +
mount -a
  
 
[[Category:Arduino/RaspberryPi]]
 
[[Category:Arduino/RaspberryPi]]

Latest revision as of 09:47, 2 December 2017

Decided time to switch to new os and Python 3, this is more or less a log


Contents

[edit] Download ....

Use this for install directions

said use etcher so that is what I plan to do.

[edit] Setup

next look at:


  • look at preferences from menu and enable vnc
  • in preferences set the localization to yours

[edit] Update

  • Before installing new application or service in Raspbian, make sure to always type this into terminal: ( if this file is on your PI use cut and paste ) This takes awhile ( perhaps an hour? )
sudo apt-get update
sudo apt-get upgrade
sudo apt-get dist-upgrade

You many find the following of use as well Linux Commands On Pi

[edit] Remote Desktop VNC

  • vnc

Default login. Username: pi. Password: raspberry. So, type pi, enter, raspberry, enter.


[edit] Static Ip Address

sudo leafpad /etc/dhcpcd.conf

Scroll all the way to the bottom of the file and add one, or both of the following snippets. Depending on whether you want to set a static IP address for a wired connection or a wireless connection eth0 = wired, wlan0 = wireless. You’ll need to edit the numbers in the snippet so they match your network configuration.

  • interface = This defines which network interface you are setting the configuration for.
  • static ip_address = This is the IP address that you want to set your device to. (Make sure you leave the /24 at the end)
  • static routers = This is the IP address of your gateway (probably the IP address or your router)
  • static domain_name_servers = This is the IP address of your DNS (probably the IP address of your router). You can add multiple IP addresses here separated with a single space.
  • my next Raspberry Pi 182/183 I just pasted this into the bottom of the file

interface eth0

static ip_address=192.168.0.182/24
static routers=192.168.0.1
static domain_name_servers=192.168.0.1

interface wlan0

static ip_address=192.168.0.183/24
static routers=192.168.0.1
static domain_name_servers=192.168.0.1

then sudo reboot to try it out - ivp 6 may be a good addition to look into

this does part of wifi, but need more

[edit] finish get wifi working

[edit] software installed with package manager

spyder3 arduino stuff


[edit] Share Net Drive

which samba	             

did not show samba but

sudo apt-get install samba

showed it was there -- not this time it did a big install ?? did it remove and install, the mysteries continue

>>> create mount point

sudo mkdir /mnt/share1

this gave read access

sudo mount -t  cifs -o guest  //192.168.0.170/share /mnt/share1

read write with this

sudo mount -t cifs -o username="russ",password="passwordhere",workgroup="MSHOME",file_mode=0777,dir_mode=0777,nobrl //192.168.0.170/share/_Source/rPi  /mnt/share1

[edit] Make automatic with fstab

https://rasspberrypi.wordpress.com/2012/09/04/mounting-and-automounting-windows-shares-on-raspberry-pi/

2.2 Password Protected Share sudo mount -t cifs -o username=yourusername,password=yourpassword //WindowsPC/share1 /mnt/mountfoldername 3. Now to check that its mounted , run the following command $ df -h

[edit] using fstab

  1. using fstab this will let you auto mount

for nano ctrl O writes a file

sudo leafpad /etc/fstab
sudo nano    /etc/fstab            


note that fstab may be hidden file >> //192.168.0.170/share/_Source/rPi /mnt/share1 cifs user=russ,pass=<password_notin_quotes??>,_netdev 0,0


rp-cifsinfstab

this looks good for stab

mounting-and-automounting-windows-shares-on-raspberry-pi/


 # For Guest Login
     //WindowsPC/Share1 /mnt/mountfoldername cifs guest 0 0

For Password Protected Login //WindowsPC/Share1 /mnt/mountfoldername cifs username=yourusername,password=yourpassword 0 0

//192.168.0.170/share/_Source/rPi /mnt/share1 cifs user=russ,pass=squeak13,_netdev 0,0

If you make a new entry in fstab it will not auto-mount. Therefore you must reload / refresh the entries. A reboot will do this but that is not a friendly way to do it. A quick way to reload new entries in /etc/fstab (fstab) is to use the mount command:

mount -a

Personal tools
Namespaces

Variants
Actions
Navigation
Toolbox