Motherboards that run Linux
Elphel cameras are free software and open hardware cameras. The cameras run Linux. The cameras have several interfaces -- 10/100 Ethernet, USB, IDE, RS-232, etc. It uses a FPGA for video processing and video compression. More information here at Open Circuits: Elphel camera; and at the Elphel wiki.
An ARM920T board running Linux at 200 Mips with sound, Ethernet, CAN, 48+ bidirectionnal IOs and 4 DSPs for motor control (DC, Servos, etc...). Built as a student proof robotics design platform.
The Bifferboard has:
- 150MHz CPU, Intel 486SX instruction set, MMU.
- 1 watt power consumption (200mA @5v)
- 68mm x 28mm x 21mm (weight 28g)
- 32MB SDRAM/8MB Flash
- OHCI/EHCI USB 2.0
- 10/100 ethernet
- Serial console 115200 baud (can be used as 2 GPIO)
- 4-pin JTAG (can be used as GPIO)
- 2 permanent GPIO (1 LED, 1 button)
The Balloon project has produced Balloon3, a high-performance ARM board designed for use by OEMs and Higher education. Spec is PXA270 (583Mhz), FPGA or CPLD, 1GB flash, 784MB RAM, USB (master, slave, OTG), CF slot, expansion bus, 16-bit bus, I2C, LCD, serial, audio. Very low power in CPLD confiuguration. Small, light. Various add-on boards: VGA LCD driver, robot motor driver+A/D, digital IO. Released under the Balloon Open Hardware license, which allows anyone to manufacture and for people to make derivatives. The expansion bus allows balloon to be used as the computing component for various special-purpose devices.
- "Aleph One is shipping a one-ounce, one-watt, 206MHz StrongARM-based single-board computer (SBC) that comes pre-installed with embedded Linux and features an "open source" hardware design." 2004.
The linuxstamp is an open source processor module. It is designed to be a very simple board capable of running linux. It is based on the Atmel AT91RM9200 processor (An ARM9 processor with a MMU).
This is the first mother board for the linuxstamp. It is still in the planning stages (no pcbs).
The Linuxstamp II is an open source processor module. It is designed to be a very simple board capable of running linux. It is based on the Atmel AT91SAM9260 processor (An ARM9 processor with a MMU).
Motherboard for the Linuxstamp II to interface with RC servos.
LART -- an open license StrongARM based tiny SBC
http://www.linuxdevices.com/links/LK9764937601.html (broken link)
LART -- an open license StrongARM based tiny SBC.
"All CAD files required for building LART are available under the closest we could get to an Open/Free Hardware License." The link in the Linux Devices article no longer works; the most recent link is http://www.lartmaker.nl/ . 75 mm x 100 mm.
- "Tiny "open hardware" SBC now available commercially": "Aleph One Ltd and Remote12 ... announce that they are able to supply LART boards, with a User Guide, software and cables." 2001.
- "Open hardware for open software" "Aleph One Ltd of Cambridge, England and Remote 12 Systems Ltd of London, England are now able to supply both LART and KSB boards, plus a User Guide, software, and cables." 2001. "The KSB board plugs onto LART and provides: IDE/ATA interface (44 pins on 2mm centers); stereo 16-bit 44KHz audio output at line and headphone levels; PS/2 connections for mouse and keyboard; mono audio I/O, POTS and ADC fron a UCB 1200chip; connectors for IrDA, USB Client, video, and touchscreen."
- "More LART SBCs?" 2002.
A Gumstix motherboard is called a COM, which stands for computer-on-module. Gumstix COMs are inexpensive, and have RAM/Flash, 802.11b/g, Bluetooth and power management "on COM". Each COM connects to a wide variety of openly published expansion boards that include USB interface (gadget mode and host mode) and have things like Ethernet, GPIO and LCD module interface.
An Overo COM is powered by a Texas Instruments ARM-based Stellaris, DaVinci or OMAP 35xx processor. A Verdex Pro COM is driven by a Marvel PXA270 (Verdex Pro series).
Very cool site.
All expansion boards are open hardware.
The Raspberry Pi is a low-cost (USD $35; GBP ~£22) credit-card sized Linux computer for teaching computer programming to children.
The same system sofware (Linux and mostly open-source software) runs on a very similar "Chumby Hacker Board" available from adafruit.
The Chumby wiki discusses the Chumby from chumby.com, the CHB from adafruit, and a few other closely related devices.
(Is there a better page for open-source storage hardware?)
Many people have published all the details needed to build a network-attached storage device (NAS), typically running Linux or other open-source OS. Alas, most of them use some proprietary motherboard, rather than the open-hardware motherboards elsewhere on this page.
In no particular order:
DIY NAS "Do It Yourself NAS" .
"Top 10 Linux Networked Storage Systems Under $1,000" .
"Storage Pod 4.0: Direct Wire Drives – Faster, Simpler and Less Expensive" .
"180TB of Good Vibrations – Storage Pod 3.0" "we open sourced the Backblaze Storage Pod design and introduced the world’s most cost-efficient way to store big data." 
"18TB Home NAS/HTPC with ZFS on Linux". .
"advice on cheap hardware for debian NAS"]. 
"the FreeNAS project". .
"How to build your own NAS box". with OpenMediaVault (OMV). .
"Building a tiny low-power Linux NAS". .
"Building a NAS Server". .
The Linksys NSLU2 , a.k.a. the "Slug", is a small low cost network storage device from Linksys. It can be flashed with Unslung, SlugOS, Debian/NSLU2 or OpenWrt/NSLU2 open-source firmware.
- "OpenWrt on the NSLU2".
- "Debian on a Slug".
- "Linux-based SLUG spawns highly hackable NAS (LinuxDevices)".
Other Boards that Run Linux
- Is it possible to Linux on a "soft CPU" inside a FPGA?
- FriendlyARM produces several motherboards that support running Linux and Android (comparison), and posts the schematics for each one online. Is that close enough to open hardware?
- Most Open Mobile Gadgets run Linux
- Linux Devices: "Single Board Computer (SBC) Quick Reference Guide" lists a huge number of single-board computers that run Linux, from very tiny, low-power, specialized boards, to standard PC/104 and PC/104-Plus SBCs (96 mm × 90 mm) to Mini-ITX (170 mm × 170 mm) to EBX motherboards (203 mm × 146 mm).
- The ARM9 AT91SAM9261 is capable of running Linux.
http://www.linuxdevices.com/articles/AT8498487406.html (broken link)"teeny weeny Linux single board computers"
- $49 (?) Yoggie Open Firewall runs Linux on an ARM PXA270 @ 520MHz
- Armadeus boards run Linux with a Freescale 400MHz i.MX27 ARM926 processor. There is a Armadeus Project Wiki.
- Beagle Board is an open-hardware board] that runs Linux on a Texas Instruments OMAP3530 system-on-a-chip, which includes an ARM Cortex-A8 CPU, a TMS320C64x+ DSP ... supported by the Texas Instruments company.
- the Analog Devices Blackfin was one of the first DSPs to run Linux.
- the ADI Blackfin STAMP Board has a Analog Devices Blackfin ADSP-BF533 running uClinux.
- the ADSP-BF537 STAMP has a Analog Devices Blackfin ADSP-BF537 running at 500 MHz ... but does it run Linux?
- the Blackfin Handy Board has a Analog Devices Blackfin ADSP-BF537 running at 600 MHz plus a Xilinx Spartan 3e FPGA ... but does it run Linux?
- the uClinux project's "Blackfin" wiki pages has a list of devices that apparently all run uClinux on a Blackfin.
- Dragonix, an 'open hardware' Linux SBC, based on a Motorola Dragonball 68VZ328 processor, running uClinux. 100 x 100 mm. Designed to have a 2.5-inch IDE hard drive mounted to it.
- Are all the motherboards listed at "Seeking very small web server" already listed here?
- Are all the devices listed at "What's the simplest Linux capable board I could make at home?" already listed here?