Difference between revisions of "Connectors"

From OpenCircuits
Jump to navigation Jump to search
m (Reverted edits by Animalvoyage2 (talk) to last revision by DavidCary)
Line 1: Line 1:
[http://www.fooditud.com/blogs/133983/138788/machine-keys-and-pins Hardware Commercial][http://eyeuser.com/blogs/viewstory/1039620 Machine Keys and Pins],  [http://satisfactionevent.com/activity/p/333216/ Rivets]High power alloy alloys.
+
[[Image:Main-GM862header.jpg|69px|GM862 SMD Connector]]
 +
[[GM862 SMD Connector]]
  
To make certain stableness towards buckling from the with regard to plate, elaborate designs for spar sections were devised.
+
[[Image:Main-DB9-PCB-1.jpg||69px|DB9 Connector]]
 +
[[DB9 Serial Connector]]
  
In 1909 Alfred Wilm, inside Germany, inadvertently identified that an aluminum metal containing 3.5 % copper, 0.5 per cent magnesium mineral as well as silicon and iron, as unintentional impurities, spontaneously hardened following quenching coming from about 480??C. The patent rights with this like a have been purchased through Durener Metallwerke who promoted the alloy as Duralumin. For half a century this particular alloy has been utilized within the wrought heat-treated, naturally older condition. Located about the outboard percentage with the wing, they enable the plane to show in regards to the longitudinal axis.
+
[[Image:Main-Barrel-Connector.jpg|69px|Barrel Jack]]
 +
[[Barrel Power Jack]]
  
When the best aileron will be moved upward, the remaining one goes down, thus resulting in the planes to be able to move to the right. Because this course of action creates a huge force, the actual ailerons should be made so regarding stand up to it.
+
[[Image:Mini-USB.jpg|69px|Mini-USB]]
 +
[[Mini-USB SMD connector]]
  
Flight handles additional compared to the three primary kinds are expected on high-performance aircraft. On the particular wings of a wide-body jet, regarding example, there are as much as tough luck trip controls, which includes higher and also low-speed ailerons, flaps, as well as spoilers.
+
[[Image:sf-microsd.jpg|69px|Mini-USB]]
 +
[[MicroSD/Transflash Socket]]
  
Flaps And Spoilers
+
UEXT: universal expansion connector. The standard UEXT connector consists of ten pins (two rows of five, with 0.1" spacing) and supports I2C, SPI, and RS-232 serial communication, as well as carrying +3.3V power and common ground. -- [http://en.wikipedia.org/wiki/UEXT Wikipedia: UEXT]
  
Wing flaps their elevate regarding take-off and landing. Inboard and also outboard flaps, on the looking side with the wing, travel from complete up, that is neutral aerodynamic movement position, to be able to full down, leading to air to be able to accumulate and make lift. Leading side flaps : Krueger flaps as well as variable-camber flaps -- their particular wing note dimension and so enable the planes to consider off or even land on a reduced runway. Spoilers, found in the center part span-wise, function a couple of purposes. They assist the particular high-speed ailerons inside switching the actual aircraft during flight, plus they are used to get rid of the sleek raise in the course of landing simply by dispersing open up about touchdown.
+
[[JTAG]] connectors?
  
Trim Tabs
+
[[ideas#better data cable ideas]]
  
Connected for the main flight controls tend to be devices known as reduce tabs. They are employed to make fine changes for the trip path of the aircraft. Trim tabs are built just like wings or even ailerons, but are
+
Some connector companies in no particular order:
considerably smaller.
+
[[Samtec]], [[Molex]],  
  
Airframe components
+
Rather than wiring a connector up directly to a CPU, one typically has some [[input protection]] between them.
  
Almost any airframe may be split into four principal components:
+
The [[SFE Footprint Library]] includes a few connectors.
  
• the particular mainplane or perhaps wings
+
Mark Whitis has a list of "common pitfalls of Micro Development Boards".
 +
He describes how the 26 pin connectors on his
 +
[http://www.freelabs.com/~whitis/electronics/9S12DP256/micro_board/ Mark Whitis Microcontroller Development Board]
 +
avoid those pitfalls and
 +
have many non-obvious features that make them superior to many other connectors.
  
• the actual fuselage or perhaps body
+
[http://techref.massmind.org/techref/pcbixmax.htm Massmind: "Maximum interconnect options from minimum board space"]
 +
discusses a board pattern that gives you the option of plugging in any one of a variety of different connectors.
  
• the actual end unit (or foreplanes, for a canard-type aircraft)
+
Connectors and data cable ideas are further discussed at [[Ideas#better_data_cable_ideas]].
  
• mountings for many other systems (undercarriage, engines, etc.)
+
[[Category:Connectors]][[Category:Components]]
 
 
Each principal element is designed to perform a certain task, so the complete airframe can easily carry out the task for which it was developed inside a safe as well as successful way.
 
 
 
Airframe would not and also design
 
 
 
All aircraft are usually composed of a lot of individual parts, and each portion has its own specific career to do. But even when that had been achievable to create an aircraft in a single piece, this particular wouldn't normally be the best option. Some elements will end up damaged, degrade or break in the course of service, and also supply must be created for his or her restore or even replacement.
 

Revision as of 12:37, 19 April 2014

GM862 SMD Connector GM862 SMD Connector

DB9 Connector DB9 Serial Connector

Barrel Jack Barrel Power Jack

Mini-USB Mini-USB SMD connector

Mini-USB MicroSD/Transflash Socket

UEXT: universal expansion connector. The standard UEXT connector consists of ten pins (two rows of five, with 0.1" spacing) and supports I2C, SPI, and RS-232 serial communication, as well as carrying +3.3V power and common ground. -- Wikipedia: UEXT

JTAG connectors?

ideas#better data cable ideas

Some connector companies in no particular order: Samtec, Molex,

Rather than wiring a connector up directly to a CPU, one typically has some input protection between them.

The SFE Footprint Library includes a few connectors.

Mark Whitis has a list of "common pitfalls of Micro Development Boards". He describes how the 26 pin connectors on his Mark Whitis Microcontroller Development Board avoid those pitfalls and have many non-obvious features that make them superior to many other connectors.

Massmind: "Maximum interconnect options from minimum board space" discusses a board pattern that gives you the option of plugging in any one of a variety of different connectors.

Connectors and data cable ideas are further discussed at Ideas#better_data_cable_ideas.