Editing Basic soldering

== Basic Soldering ==
Required tools:
Hot metal object (preferably with an insulating handle like in a soldering iron)
Solder (preferably with rosin flux core)

Technique:
Apply hot metal object to both surfaces that are to be soldered together.  Feed the flux-core solder into the joint from the side opposite the h.m.o. (soldering iron)  Once enough solder has flowed, remove heat.

If you have difficulty in holding two objects in place whilst you solder them try using the product "Blu-Tac" ([http://en.wikipedia.org/wiki/Blu-tac]) or similar. Blu-tac is non-conductive and moderately resistant to heat (that said you can still burn it without a lot of heat, creating a bad smell, probably not good to breathe either) 

The major advantage of Blu-tac over a vice or other mechanical holding option is that you can make infinitesimal adjustments with your fingers quickly and accurately. 

Preferred tools:
A temperature-controlled soldering iron/station.  
Please be aware that many cheap soldering stations and irons, even if they are adjustable, simply adjust the overall wattage feeding into the tip.  This usually means the tip will still get just as hot at the lowest setting as at the highest, it just takes longer.  Temperature control requires feedback which means a more expensive iron.  Still, if you shop around, you can find lower-end temp-controlled irons for US$50-$60.  The recommended temperature is around 380F for 63-37 (tin-lead ratio).  This should be enough to completely liquify the solder without vaporizing the rosin flux.  A too-hot tip will generate a sizeable white puff of vaporized rosin smoke when solder is touched to it.  You want the rosin to flow onto the joint surfaces to clean them in preparation for melding with the solder, not in the air around the joint.
Thin (fine-pitch) rosin-core solder.
Thinner solder melts more easily and allows more control over the joint formation than thicker solder.  Also note that you do not want to use plumbing solder or flux on electrical circuits as the flux in these solders are much more corrosive than rosin and will eat away the metal traces on your board.

== Advanced Soldering ==
The [http://www.psocdeveloper.com/forums/viewtopic.php?t=2358 "Packaging information"] thread
has a few tips for soldering surface-mount (SMT) components:
SOIC (1.27mm/50 mil pitch), SSOP (0.65mm pitch), TQFP (0.50mm-0.80mm pitch), and MLF/QFN (0.50mm pitch).

== Desoldering ==
Solder suckers can be hand-held, pump-driven, and with or without active heating.  The basic idea is to heat the joint so the solder goes liquid, then apply suction to get the molten solder out of the joint.  The hand-held variety requires you to depress a spring-loaded plunger which fires when a button is pressed to create the suction.  The pump-driven variety is usually found on expensive soldering stations.  Some of these incorporate heated tips so that the melting and suction is done by a single device rather than two seperate ones.

Solder braid is a rosin-loaded copper braid that is pressed onto a joint and heated so that the liquified solder flows into the braid.  Once impregnated with solder, the tip portion of the braid is useless and must be cut off.  Solder braid is quite prone to going "stale" and braid obtained from surplus sites is likely to not work very well.

Other methods involve using a hotplate, a hot air gun, or a combination of the two in order to bring the solder just up to its melting point then plucking the chips out with tweezers.

== Links ==

* [[Skillet reflow]]
[http://www.elexp.com/t_solder.htm Electronix Express Soldering Tips]

* [http://radiojove.gsfc.nasa.gov/telescope/soldering.htm Instructional Soldering Videos from NASA]

[http://www.inlandcraft.com/Uguides/tipfailure.htm InlandCraft Tip Failure Article]

* [http://www.geofex.com/Article_Folders/how_to_solder.htm Geofex.com How-To Solder]

[http://www.curiousinventor.com/guides/Surface_Mount_Soldering Video "How to solder SMD" from curiousinventor.com]

* [http://www.curiousinventor.com/guides/How_To_Solder Video "How to solder properly" from curiousinventor.com]

[[Category:Techniques]]
@@ Line 31: / Line 31: @@
 == Links ==
-* [[skillet reflow]]
+* [[Skillet reflow]]
-* [[toaster oven]]
+[http://www.elexp.com/t_solder.htm Electronix Express Soldering Tips]
-* the PIClist thread [http://www.piclist.org/techref/postbot.asp?by=thread&id=Looking+for+SMT+Prototype-suitable+solder&w=body&tgt=post "Looking for SMT Prototype-suitable soldering station"] has a few soldering iron recommendations, including
-** Weller
-** [http://www.ntscope.com/Merchant2/merchant.mvc?Screen=PROD&Store_Code=MTC&Product_Code=QK202D $130 Madell QK202D Soldering Station]
-** [http://store.sra-solder.com/product.php?xProd=6144&xSec=22 $40 Aoyue Basic Soldering Station 936]
-* [http://www.elexp.com/Images/Weller_Coping_with_Lead_Free.pdf Electronix Express "Soldering tips and lifetime issues"]
-* [http://www.elexp.com/Images/Better_Soldering.pdf "Better Soldering"]
 * [http://radiojove.gsfc.nasa.gov/telescope/soldering.htm Instructional Soldering Videos from NASA]